Oxford shoes are a staple in a man’s shoe collection. They’re casual and dressy, making them perfect for all occasions. The one downside is that they’re not easy to lace up. There are two ways in which you can lace oxfords in order to secure the shoe onto your foot: You can either use an “oxford bow” or the “crossover” method.
See: Beautiful Lace Jumpsuit For Ladies
The following guide will teach you how to do both, so you can tie your shoes quickly and easily!
Introduction to Lacing Oxfords
When it comes to lacing oxfords, there are two primary ways in which the shoe lace can be tied. The “oxford bow” is an easy method that will allow you to quickly secure your shoes onto your foot.
The “crossover” method is a little more complicated but makes for a much tighter knot. This is the best method when you want to make sure your shoes stay on securely.
Lacing oxfords with either of these methods is relatively easy and should take no longer than 10 seconds each.
How to Tie an Oxford Bow
The Oxford Bow is a shoe-tying method that can be used to secure your Oxford Oxfords. It’s an easy and traditional way of tying your shoes that is popular because it allows for quick, easy, and secure lacing of your oxfords.
To do the Oxford Bow, first you need to make sure that your laces are at the correct length. If they’re too long, you’ll need to shorten them by cutting them off. You should also ensure they’re strong enough to hold up your shoe while you tie the bow.
Next, take one lace and tie it around the front part of the top of one shoe so it creates a loop. Next, take the other lace and tie it through both loops on the same shoe until you create a second loop on the opposite side. Repeat this process with all three loops until you have three left untied, leaving enough space for tying an Oxford Bow.
Once all six loops are tied together in an Oxford Bow using all three pairs of laces, pull each pair tight until they create a knot at each end of the bow. The last step is to pull each knot tight so they’re joined tightly together in order to secure the bow onto your
How to Tie an Oxford Crossover
The crossover method is used to tie oxfords that are too small for the bow.
Begin by loosening the shoe’s laces and then looping them in a circle around your hand.
Next, tuck one end of the lace into the other so they’re crossed over one another.
Using one hand, bring both laces over your opposite index finger and pull them down until they rest in front of your shoes.
Now, use your pointer finger to grab the left lace and place it on top of the right lace. Place your thumb on top of this left lace and then pull it up towards you so that it creates a loop between the two laces once again. Finally, do this with the right lace as well so you have created a “Y” shape between these two loops with your hands in order to create an “oxford bow.”
Once you’ve done this, use both hands to tighten each loop below the “oxford bow,” just as if you were tying a shoe normally. This will keep everything secure without having to tie an actual bow.
How to Lace Oxford Shoes with an Oxford Bow
Step 1: Place the shoe on your foot so that the heel is at the back.
Step 2: Cross one lace over the other.
Step 3: Pass one lace through a second hole of the other lace and exit it to create a loop.
Step 4: Pass this loop over the opposite lace and through a third hole on that same lace, as well as a fourth hole on the opposite lace.
Step 5: Pull both laces tight to create a knot in both loops and then pull them together.
Step 6: Insert your foot into the shoe with the laces laid out flat across your instep and pull both laces up tightly.
See: Top 10 Places to Spend Christmas in the UK
To lace up your shoes using the crossover method, start by folding your laces in half. Next, cross one lace over the other and pull up on both sides. This will secure one side of the shoe to your foot.
Now repeat this process on the other side of the shoe, and you’ve successfully laced your oxfords!